Accessories for die clamping technology
Elements for oil supply to hydraulic elements.
Fittings | High-pressure hoses | Couplings | Connecting blocks | Plug-in connectors | Hydraulic valves | Pressure gauges| Pressure switches | Hydraulic oil | Clamping pumps
Product series (4)
fittings
max. operating pressure 400 bar, sealing using sealing ring and sealing cone
see
High pressure hoses ND4
in variable lengths and connectors
The freely selectable hose lengths should be generously dimensioned, in order to avoid kinking, abrasion marks, torsion, tensile and compressive stress and unacceptable bending radii. Protect against hot swarf.
Burst pressure 2000 bar, smallest bending radius 100 mm.
*Further information see DIN 20066
11.3800 High-pressure hose ND4
11.3800 Hose connections left/right
Quick-disconnect coupling G 1/4
The quick-disconnect coupling is a coupling of sturdy design which locks automatically after uncoupling. Connection and disconnection is made in the unpressurised condition. The displacement of the sleeve to the corresponding coupling or uncoupling direction enables an easy one-hand operation.
11.3800 Quick-disconnect coupling
Connector block
with pilot-operated check valves
connecting threads:
- 2 x G 3/8 + 6 x G 1/4
- 8 x G 3/8
11.3800 Connecting block
Plug-in connectors
for plates and piping boards
max. 500 bar, nominal diameter 5 mm,
short or long version
Plug-in connectors for plates and piping boards
Directional control valve WH1
3/2 directional control valve with leak-free and tight ball-type poppet valves
Compact design by integration of the valve components in the magnetic body.
max. flow rate 8 l/min, max. operating pressure 400 bar, magnetic clamping 24 VDC,
temperature range -40°C to +80°, emergency stop
Directional control valve (WH1) 11.9200
Pressure switch
Mini pressure switch, adjustable as a piston pressure switch
temperature range -40°C to +80°,
max. operating pressure 400 bar (depending on the type).
Versions: HDS and DG
see
Pressure switch HDS with connecting plate
Pressure relief valve
Safety valve to prevent exceeding the maximum admissible pressure and for limiting operating pressures.
11.9200 Pressure relief valve
Pressure control valve
Pressure control valve for keeping the lower output pressure in the secondary circuit constant without affecting the higher pressure in the primary circuit.
Screw-in type valve in combination with connector block.
11.9200 Pressure control valve
Pressure gauge
with steel tube spring and glycerine filling, Ø 63 mm
Port: G1/4 at the bottom or at the rear
11.9200 Pressure gauge
Check valve
Stop valve with free flow in one direction and blocked oil flow in the opposite direction.
11.9200 Check valve
Check valve to be installed in the pipe
Check valves with one flow direction. Housing made from galvanised steel. Spring-loaded ball-type poppet valve, leakage-free
11.9200 Check valve to be installed in the pipe
Hydraulic oil
HLP32 or HLP 46
containers: 1 or 5 litres
Hydraulic oil Oemeta
fire-resistant
containers: 1.5 or 20 litres
Hydraulic clamping pump 8.800
Compact hydraulic pump with hand lever or foot pedal for pumping and releasing.
Due to the metallic seal on the pump piston, the pump is almost wear-free.
The hydraulic pump is delivered completely assembled, including the filling with hydraulic oil HLP32 as a ready-for-connection unit.
In addition to three maximum operating pressures, the following options can be selected:
• Holder for fixing the pump at the press bed or with a base for good stability.
• Pressure gauge to display the pressure reached. Display range 0 to 100 / 120 or 400 bar.
• Adjusted overload protection (DBV) to protect the roller and ball bars against damage.
Hydraulic clamping pump 8.800
